Fix: Network Protocol Missing in Windows 10 – Solution

0

Network Protocol Missing in Windows 10: The Networking is a large part of the Windows 10 experience and one of the most annoying network problems is the one where Network Protocols are missing. This error sounds serious, so let us see if there is a way to fix this problem. Users report that they are unable to share files between network computers and some are even unable to access the internet connection. Since you can see this issue can cause a lot of inconveniences but there are a few solutions available.

How To Fix Networking Protocol Missing in Windows 10:

The Network protocol missing problem there are a few other problems that could be caused by same culprits. For example:

  • “Windows socket registry entries required for network connectivity are missing”.
  • “One or more network protocol is missing on this computer”.
  • “Could not add the requested feature”.
  • “Network protocols missing error Window 10”.
  • “One or more network protocols are missing on this computer WiFi”

So does not matter the problem code you can apply the solution from below and can solve your problem.

Fix_ Network Protocol Missing in Windows 10 - Solution

Fix: Network Protocol Missing Problem on Windows 10:

Solution 1. Temporarily Disable Your Antivirus Software:

Although it is not a good opinion to disable your anti-virus software some of the users report that after disabling Kaspersky internet security 2016 their problem have been resolved. So if you are using Kaspersky internet security 2016 you might suppose disabling it temporarily or switching to a various antivirus software. In addition, reinstalling antivirus software could also be helpful.

Temporarily Disable Your Antivirus Software

Solution 2. Restore Network Protocols to Default Settings:

The extra thing we are going to try is resetting network protocols to default settings. We are going to do this by resetting the TCP/IP stack. In case you are not sure how to do this so follow this steps.

1.Open Command prompt.

2.After opening Command prompt enter the following lines:

  • netsh int ip set dns
  • netsh winsock reset

3. Close Command prompt and check if the problem is solved are not.

Restore Network Protocols to Default Settings

Solution 3. Disable NetBIOS:

  1. Open control panel> Network and Internet> Network Connection.
  2. Right-click on the adapter and select Properties.
  3. Highlight IP v4 and select properties.
  4. Click Advanced.
  5. Go to the WINS and in NetBIOS setting section select Disable NetBIOS over TCP/IP.
  6. Click on OK button to save the changes.

Some of the users also claim that this problem is resolved by using obtaining IP address automatically instead of using a static IP. As soon as you open IP v4 properties you should see the option that allows you select whether you need to use static IP address or to obtain one automatically.

Disable NetBIOS

Solution 4. Use Command Prompt:

  1. Run Command Prompt as a administrator.
  2. When it starts type netcfg -d and press Enter to run it.
  3. Wait for the process to complete after completing the process your computer should restart and the problem should be resolved.

In extension to some users suggest using the netsh int ipv4 install command. Start the Command prompt as administrator like in step 1 and type netsh int ipv4 install into Command prompt and press Enter to run it. Restart your computer to fix the problem.

Use Command Prompt

Solution 5. Use Command Prompt and sc.exe:

This solution is a temporary solution and you might have to return the changes after a new Window 10 update if the issue starts occurring again follow steps:

  1. Open Command Prompt.
  2. Typen the following lines:
  • sc.exe config lanmanworkstation depend= browser/mrxsmb10/nsi
  • sc.exe config mrxsmb20 start= disable

After entering the above lines into command prompt the problem should be solved. If you started to have trouble after a Windows 10 update you might need to restore the default settings. To do follow the steps:

  1. Open Command Prompt.
  2. Enter these lines
  • sc.exe config lanmanworkstation depend= browser/mrxsmb10/mrxsmb20/nsi
  • sc.exe config mrxsmb20 start= auto

Use Command Prompt and sc.exe

The Quick Solution to Fix the Network Protocol Missing Problem on Windows 10:

Step 1: Download this PC scan and Repair tool.

Step 2: Click on start scan to find the window problem that causing a network protocol missing error in windows 10.

Step 3: Click start Repair to fix all the problems.

Hope now you came to know how to fix the Network Protocol Missing error in Windows 10. If you still have any queries regarding this article feel free to comment on comment section thank you.

LEAVE A REPLY

Please enter your comment!
Please enter your name here